ASTM B283 PDF

ASTM B/BM: Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed). ASTM B Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)1_机械/仪表_工程科技_专业资料。ASTM 标准. ASTM B/BM Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed). standard by ASTM International.

Author: Zulkirg Takinos
Country: Libya
Language: English (Spanish)
Genre: Life
Published (Last): 19 November 2010
Pages: 384
PDF File Size: 10.12 Mb
ePub File Size: 19.39 Mb
ISBN: 685-8-22728-185-9
Downloads: 75589
Price: Free* [*Free Regsitration Required]
Uploader: Kegrel

Active view current version of standard. Distributors will offer small quantity buys while mills will generally only sell large quantities, with delivery times anywhere from 10 to 50 weeks depending on size and form required This material is stocked primarily in Flat Rolled Products by 2 distributors but is also available to a lesser extent in Bar Products.

The shear wave entrant angle shall be such to ensure re?

Soldering is rated as “excellent”, brazing is rated as “good”, oxyacetylene welding is “not recommended”, gas shielded arc welding is “not recommended”, coated metal arc welding is “not recommended”, spot welding is “not recommended”, seam welding is “not recommended”, and butt welding is rated as “fair”.

Notches shall be made either in the piece to be examined or in a separate defect-free specimen of the same size within 61? Work Item s – proposed revisions of this standard. The following copper and copper alloys are included: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The following copper and copper alloys are included: Note 1 — Nominal composition and relative forgeability ratings are given in Appendix X1.

This specification establishes the requirements for copper and copper die forgings produced by hot pressing method.

  BUILDING SEARCH APPLICATIONS WITH LUCENE AND NUTCH PDF

C Copper Alloys Material Property Data Sheet – Product availability and request a quote

Notch length shall not exceed 1 in. The following copper and copper alloys are included:. H Carbon shall be 0. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Therefore, the data in Table X3.

Copper-nickel alloys C and C are intended for welded applications with ashm exposure. The product also shall be inspected with a b2883 wave test from the external circumferential and end surfaces. C shall be heat treated as follows: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Modulus of Elasticity Tension. Mechanical Property Requirements 9. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Copper-nickel alloys C and C are intended for welded applications with seawater exposure.

G Iron content shall not exceed nickel content. C and C shall be heat treated as speci? Material shall be tested using a square, rectangular, or circular transducer having an effective area of 1 in.

Bb283 is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Active h283 current version of standard.

ASTM B Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)1_百度文库

B One or more of these elements may be present adtm speci? Where Alloy FC Brass is Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. C and C shall depend only on tensile strength.

Work Item s – proposed revisions of this asym. D Other deoxidizers may be used as agreed upon, in which case phosphorus need not be present. The values shown represent the general opinion and are ast for information to enable the adtm to better understand the forging characteristics of these various alloys. This standard does not purport to address all of the safety concerns, if any, associated with its use. Recalibration shall be performed at least once per 8-h shift.

  LINIENNETZ WIEN PDF

Thin section, long over 6 in. Solid Solid, with symmetrical cavity Solid, with eccentric cavity Solid, b238 extrusion Hollow, deep extrusion Thin section, short up to 6 in. Combining values from the two systems may result in non-conformance with the standard.

The capacity for cold working this alloy is rated as “poor”. The following copper and copper alloys are included: Dimensions and Permissible Variations The derived SI unit for force is the newton Nwhich is de? Special Government Requirements The position and amplitude of the response from each notch shall be marked on the instrument screen or a transparent overlay, and these marks shall be used as the evaluation reference.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

A B Silver counting as copper.

C37700 Copper Alloys Material Property Data Sheet – Product availability and request a quote

E This includes copper plus silver plus sulfur plus phosphorus. F For boiler code application maximum iron content shall be 4. This standard does not purport to address all of the safety concerns, if any, associated with its use. Originally approved in