ASTM D3045 PDF

ASTM D Standard Practice for Heat Aging of Plastics Without Load 1 1 x00a0 This practice is intended to define the exposure conditions for evaluating. Standard Practice for Heat Aging of Plastics Without Load – ASTM D Status: Withdrawn ยท Replaced by: ASTM D Buy this standard. Price: . ASTM D(). Standard Practice for Heat Aging of Plastics Without Load. standard by ASTM International, 03/15/ This document has been.

Author: Nehn Voodoohn
Country: Mayotte
Language: English (Spanish)
Genre: Marketing
Published (Last): 5 April 2015
Pages: 99
PDF File Size: 9.47 Mb
ePub File Size: 7.23 Mb
ISBN: 474-4-14924-750-8
Downloads: 33339
Price: Free* [*Free Regsitration Required]
Uploader: Zolokora

Therefore, for any application of the CUT or the TI temperature index to be valid, either the thermal aging program must duplicate the intended thermal exposure conditions of the end product, or the Arrhenius relation must apply.

However, extended periods of exposure of plastics to elevated temperatures will generally cause some degradation, with progressive changes in physical properties.

Caution should be exercised in using the Arrhenius relation and knowledge of axtm changes in the material at elevated temperatures is important.

Standard – Standard Practice for Heat Aging of Plastics Without Load ASTM D –

Subscription pricing is determined by: Proceed to Checkout Continue Shopping. Only the procedure for heat exposure is specified. The effect of elevated temperature on asttm particular property is determined by selection of the appropriate test method and test specimens for that property. This standard and ISO address the same subject matter but differ in technical content. The severity of the exposures in both time and temperature determines the extent and type of change that takes place.

The effect of elevated temperature on any particular property is determined by selection of the appropriate test method and test specimens for that property. Certain materials are susceptible to the influence of humidity. Work Item s – proposed revisions of this standard. Normally, additional shrinkage should be expected with loss of volatiles or advance in polymerization.

Already Subscribed to this document. If the document is revised or amended, you will be notified by email. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Ultimate properties such as strength or elongation are more sensitive to degradation than bulk properties such as modulus, in most cases.

  22TCN 334-06 PDF

Specific properties and failure or lifetime criteria for these properties are typically chosen for the evaluation of c3045 endurance.

d3405 A plastic material is not astmm degraded by exposure to elevated temperatures. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

These transitions should be avoided both in the range of aging temperatures used, as well as in extrapolation of the lifeline. Need more than one copy? Mechanical properties, such as flexural properties, are sensitive to heat degradation and may change at a more rapid rate.

Your Alert Profile lists the documents that will be monitored. D304 procedures for determining the thermal aging characteristics of a material using a series of elevated temperatures for the purpose of estimating endurance time to a defined property change at a lower temperature are also described; the applicability of the Arrhenius relation for making predictions to other temperatures, is assumed in this case.

Standard Practice for Heat Aging of Plastics Without Load

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For instance, the arc resistance of thermosetting compounds improves up to the carbonization point of the material.

The property of interest is measured at room temperature. Link to Active This link aetm always route to the current Active version of the standard. With semi-crystalline and highly crystalline polymers, elevated temperatures may cause significant changes to the morphology of the material, invalidating or compromising that assumption.

The property of interest is measured at room temperature. We have no amendments or corrections for this standard. Recommended procedures for determining the thermal aging characteristics of a material using a series of elevated temperatures for the purpose of estimating d045 time to a defined property change at a lower temperature are also described; the applicability of the Arrhenius relation for making predictions to other temperatures, is assumed in this case.

  ALPINE MRA-D550 PDF

Errors in exposure are cumulative with time. As the voice of the U. This standard is also available to be included in Standards Subscriptions. You may delete a document from your Alert Profile at any time. However, the adtm obtained from this practice, since it does not account for the influence of stress or environment that is involved in most real life applications, must be used cautiously by the designer, who must inevitably make material choices using additional data such as creep and creep rupture that are consistent with the requirements of the specific application.

Arrhenius principles may only be used r3045 accelerate a chemical mechanism if there are no fundamental changes in the material properties.

Please first log in with a verified email before subscribing to alerts. Other types of plastics become soft and sticky, either due to sorption of volatilized plasticizer or due to breakdown of the polymer. Different properties, mechanical or electrical, f3045 not change at the same rate. Only the procedure for heat exposure is specified.

This standard is not included in any packages. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. This standard and ISO address the same subject matter but differ in technical content.

Please first verify your email before subscribing to alerts. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. Factors that affect the reproducibility of data are the degree of temperature control of the enclosure, humidity of the oven, air velocity over the specimen, and period of exposure. Standards Subsctiption may be the perfect solution. On the contrary, this practice is designed to provide data which can be used for such comparative purposes.

Add to Alert PDF. Historical Version s – view previous versions of standard.